AIThis post was created with the assistance of artificial intelligence (AI).

TL;DR

A DIY adapter built around one CH570 microcontroller turns USB serial data into greyscale text and simple graphics on an analog display. The project is a low-cost video experiment, not a general-purpose USB graphics card; colour output remains a possibility rather than a demonstrated feature.

A compact board built around a single CH570 microcontroller can turn USB data into greyscale text and rudimentary graphics on an analog display, demonstrating a low-cost, highly constrained take on a USB GPU. The project, reported by Hackaday, works as a USB serial device and generates video through pulse-width modulation; it is not a conventional graphics card, and colour output has not been established.

Before you orderOffer from Amazon

Get the latest gadgets delivered free with Prime

  • Fast, free delivery on millions of items
  • Prime Video, Amazon Music and more included
  • Member-only deals all year
Start your free Prime trial Free trial for eligible customers · Cancel anytime
As an affiliate, we earn on qualifying purchases.

The converter is assembled on a small printed circuit board with the CH570 as its only active component, alongside a few passive parts. The board itself forms both the USB-C plug and the copper-plated contact designed to fit an RCA video input. That connector approach can be sensitive to orientation: some RCA sockets use a single contact wire to meet the center pin, and the board may not connect reliably in every position.

The device presents itself to a computer as a USB Communications Device Class (CDC) device, allowing serial data to be sent to it. The project’s maker, identified as bitluni, wrote software that uses the adapter as a terminal, displaying text and simple graphics in greyscale. The analog image is produced using PWM, rather than a dedicated video-output chip.

Timing is the main engineering constraint. A crystal oscillator helps keep the generated signal synchronized with the display’s refresh rate, while the fastest operations need to use SRAM. Hackaday reports that a performance drop was traced to the compiler placing some work in flash memory. During testing, a television in wireless-reception mode also picked up a signal from a jumper wire, prompting experiments with other ways to transmit the output.

At a glance
reportWhen: Reported November 22, 2026
The developmentA maker has demonstrated a tiny USB-to-analog-video adapter using a CH570 microcontroller and a handful of passive components.
USB Video · Briefing

Could One Chip Power a DIY USB GPU? A tiny monochrome experiment

A CH570 microcontroller turns USB serial data into greyscale text and simple graphics on an analog display. It is a proof of concept, not a general-purpose graphics card.

1 chip
CH570 microcontroller
~20¢
Reported chip cost only
Nov 22, 2026
Report date

How the adapter works

USB carries serial data; the microcontroller generates analog video using pulse-width modulation.

1
Send serial data

The computer recognizes the adapter as a USB Communications Device Class device.

2
Generate video

Software turns the data into greyscale text and simple graphics.

3
Connect to a display

The small board forms the USB-C plug and an RCA video contact.

What it can and cannot do

Demonstrated
  • Greyscale text and basic graphics
  • USB serial input
  • Analog video output
Not established
  • PAL colour output
  • Compatibility with every RCA socket
  • Finished adapter cost or performance

The engineering trade-off

The minimal hardware depends on careful timing and memory placement.

Timing

Keep video synchronized

A crystal oscillator helps match the generated signal to the display refresh rate.

Memory

Use SRAM for speed

The fastest operations need SRAM; work placed in flash caused a reported performance drop.

Connection

Board-shaped RCA contact

Some sockets may connect unreliably depending on contact position and orientation.

Colour remains an experiment

The report describes SPI and overclocking as possible next steps toward a PAL colour signal, with no completed colour demonstration.

Cost caveatAbout 20 cents is the reported price of the microcontroller, not the complete adapter.
The takeaway
This is a compact demonstration of simple video generation on one microcontroller, with monochrome output proven and colour still unconfirmed.

A Minimal Route to Analog Video

The project offers a practical demonstration of how a microcontroller can generate basic graphics without a dedicated GPU or video converter. That matters to hobbyists working with small embedded systems: a single inexpensive chip and a modest number of supporting parts can produce a visible, computer-controlled output, provided the resolution and performance expectations remain limited.

It also illustrates the trade-offs behind the apparent simplicity. The design relies on careful timing, memory placement, a compatible analog input and software written for the device. Its reported price of about 20 cents for the chip describes the microcontroller cost, not necessarily the complete adapter, including the board, passive parts, assembly or development effort. The result is best understood as an experiment in low-cost video generation, not a replacement for a PC graphics card or a general-purpose USB display adapter.

Products Worth Considering

Jackery Solar Generator 1000 v2 with 200W Solar Panel, 1024Wh LiFePO4 Battery

Jackery Solar Generator 1000 v2 with 200W Solar Panel, 1024Wh LiFePO4 Battery

As an affiliate, we earn on qualifying purchases.

From Text Output to Colour Experiments

Graphics processors are now associated with demanding visual workloads, but their basic function is to generate images. This project applies that narrower definition to a small microcontroller and accepts limited performance and simple monochrome output in exchange for minimal hardware. The USB connection carries serial data; the microcontroller creates the analog video signal.

Hackaday notes that bitluni has previously produced video using an ESP32, including VGA output, and has built larger microcontroller clusters as coprocessors. In this project, the unexpected reception of the PWM signal through a jumper wire led to experiments beyond the initial wired setup. The report says that using SPI and overclocking might make a PAL colour signal possible; that is a proposed direction, not a confirmed feature of the adapter as demonstrated.

“The converter is built into one tiny PCB with only one active component, a CH570 microcontroller, and a few passive components.”

— Hackaday

Limits and Unproven Colour Output

The report does not specify the adapter’s resolution, frame rate, complete bill of materials or measured end-to-end performance. It also does not establish compatibility across different RCA sockets or displays; the board-shaped RCA contact may be orientation-sensitive. The roughly 20-cent figure refers to the microcontroller, and should not be read as a verified price for a finished device.

Most importantly, the reported working output is greyscale text and basic graphics. PAL colour is described as something the system might achieve with SPI and overclocking. No completed colour demonstration, stable transmission range or assessment of reliability is given. The wireless pickup by a television is described as an observation during testing, not as a validated wireless-video feature.

Testing the Proposed PAL Signal

The next development described is further experimentation with SPI and higher clock speeds to see whether the microcontroller can generate a PAL colour signal. The available report gives no schedule, test results or confirmation that this work will produce a reliable colour output. For now, the demonstrated milestone is a USB-connected monochrome terminal on an analog display.

Further technical details—such as supported display timings, output quality, compatibility and the full parts cost—would help readers judge how readily the design can be reproduced. Until those details or a colour test are reported, the project’s reach remains a proof of concept for simple video generation on a small microcontroller.

Source: Hackaday

Key Questions

Is this a full USB graphics card?

No. It is a basic USB-to-analog-video experiment that accepts serial data and displays greyscale text and simple graphics. It does not provide the performance or features of a conventional graphics card.

What chip does the adapter use?

The design’s only active component is a CH570 microcontroller, supported by a few passive components, including a crystal oscillator for video timing.

Can it display colour?

Colour output is not confirmed. The report says SPI and overclocking might enable a PAL colour signal, but describes this as a possibility rather than a demonstrated result.

Does the adapter cost 20 cents?

The reported figure is about 20 cents for the microcontroller. The total cost of the board, other components and assembly is not specified.

Source: Hackaday

You May Also Like

A Guide To 10 Wireless Earbuds For Everyday Listening In 2027

A 10-model roundup compares noise-cancelling, workout, compact and neckband earbuds, with key differences and buying caveats.

What’s the AI Endgame?

Exploring the current AI boom, its potential outcomes, and what remains uncertain about AI’s long-term impact on society and industry.

Bose’s First Wired Earbuds In 11 Years Add Noise Canceling

Interest is rising in a report about Bose wired earbuds with noise canceling, but the underlying announcement and product details are unconfirmed.

OLED Vs QLED Vs LED: TV Display Technologies Explained

Outstanding differences between OLED, QLED, and LED TVs can help you choose the perfect display—discover which technology suits your viewing preferences.